JobEasy
← All guides

How to price a fence job per linear foot

Build a fence quote from your own costs: posts, panels or pickets, rails, concrete, gates, labor and removal, with a worked example and a per-foot check at the end.

JobEasy · Published November 12, 2026

Customers ask for a price per foot because it is easy to compare. You can give them one, but you shouldn't build the quote that way. A flat per-foot number hides gates, corners, slopes, old fence removal and hard digging, and those are exactly the things that turn a good job into a bad one.

The better way is to price the job from its parts, then divide by the footage at the end to check it. This guide shows how, with a worked example. The numbers are examples only; use your own material costs and labor rates.

Step 1: Walk the line and measure

Measure every run separately and write down:

•Length of each run
•Corners and ends (each needs a heavier or set post)
•Gates: width, single or double, and which way they swing
•Slope: is it stepped or racked?
•Anything in the way: trees, utilities, a slab, rock, a neighbor's fence

Call for a utility locate before anyone digs. In the US the number is 811, and most states require it.

Example: a backyard with three runs of 6 ft tall wood privacy fence.

•Run A: 60 ft
•Run B: 80 ft
•Run C: 60 ft
•Total: 200 linear ft
•One 4 ft walk gate, one 10 ft double drive gate
•Two corners, two ends against the house
•150 ft of old chain link to remove

Step 2: Count the posts

Line posts usually go every 8 ft on center for wood privacy fence; check the spacing your panel or rail length needs.

•Fence footage without gates: 200 − 4 − 10 = 186 ft
•Line post spaces: 186 ÷ 8 = 23.25, so 24 spaces
•Posts: work it run by run, then add terminal posts at corners, ends and each side of each gate. Gate posts should be heavier, and set deeper.

Example count:

•Line posts: 22
•Corner and end posts: 4
•Gate posts: 4 (heavier, for the gates)
•Total: 30 posts

Step 3: Rails, pickets or panels

For a stick-built wood fence, each 8 ft section needs rails (usually three for 6 ft tall) and pickets.

•Rails: 24 sections × 3 = 72 rails, plus a few spare
•Pickets: 186 ft × 12 in ÷ 5.5 in picket width ≈ 406 pickets. Add your usual waste for splits and cuts; say 5%, so 427, rounded to 430.

If you install panels, count panels per run instead, and remember the cut panels at the end of each run.

Step 4: Concrete and hardware

Concrete per post depends on hole diameter and depth. Work it out for your spec, or use the bag maker's chart. Say your spec takes two 50 lb bags per line post and three per gate post:

•26 posts × 2 + 4 gate posts × 3 = 64 bags

Hardware: rail brackets or nails, screws, gate hinges, latches, a drop rod for the double gate, post caps if they're included.

Step 5: Price the materials

Example costs only:

ItemQuantityExample costTotal
4×4 posts26$16$416
6×6 gate posts4$45$180
2×4 rails76$7$532
Pickets430$3.20$1,376
Concrete64 bags$6.50$416
Fasteners——$120
Gate hardware (2 gates)——$210
Delivery1$75$75
Materials$3,325

Step 6: Labor and removal

Estimate crew hours for each part, from your own jobs:

•Remove and haul 150 ft of chain link: 8 crew hours
•Layout and dig 30 holes: 12 crew hours (more for rock or roots)
•Set posts: 6 crew hours
•Rails and pickets: 24 crew hours
•Build and hang two gates: 6 crew hours
•Clean-up: 2 crew hours
•Total: 58 crew hours

Use your loaded cost per person-hour (wages plus payroll taxes, workers' comp and paid time off the job). Say $36:

•58 × $36 = $2,088

Add disposal for the old fence and equipment such as an auger or a post driver:

•Dump fee for old fence: $120
•Auger rental: $110
•Total: $230

Step 7: Overhead and margin

•Direct cost: $3,325 + $2,088 + $230 = $5,643
•Overhead, say 15%: $5,643 × 1.15 = $6,489
•Margin on price, say 20%: $6,489 ÷ 0.80 = $8,112

Round to $8,100 or $8,125, whichever fits how you present prices.

Step 8: Check the price per foot

•$8,112 ÷ 200 ft = $40.56 per linear ft, gates and removal included

Now you can answer the "how much a foot?" question honestly: around $40 a foot for this job, because of the two gates and the old fence coming out. A straight run with no gates and nothing to remove would come in lower. That is a much better conversation than a flat number you have to defend later.

Price gates and extras as their own lines

Show the customer the parts that change the price:

•Each gate as its own line (a double drive gate is a lot more work than a walk gate)
•Removal and haul-off of the old fence
•Stepping or racking on a slope
•Post caps, stain or sealer, if included
•Permit, if your area needs one

This also helps when they want to cut the price: they can drop the stain or the second gate instead of asking you to drop your margin.

Common mistakes

•Pricing everything at one rate per foot, so gates, corners and removal come free.
•Forgetting the old fence. Taking it out and hauling it away is real time and real dump fees.
•Not counting terminal posts. Corners, ends and gates need more than line posts.
•Ignoring the ground. Rock, roots and slopes slow the crew; walk the line before you price it.
•Quoting from memory. Keep your post, picket, rail and concrete costs in a price book so every quote uses today's numbers. In JobEasy the price book is on your phone, so you can measure the runs and hand the customer a quote before you leave.

Quick checklist

1.Call for locates; walk and measure every run.
2.Count line, corner, end and gate posts.
3.Count rails and pickets or panels, with waste.
4.Work out concrete and hardware.
5.Price materials, including delivery.
6.Estimate crew hours, including removal.
7.Add disposal, equipment, overhead and margin.
8.Divide by the footage to check, and show gates and extras as their own lines.

Quote it on site, get the deposit by card

JobEasy prices the job from your own price book, sends the estimate to the customer’s phone and takes the deposit. See it working in the demo, no sign-up.

Open the live demo →